Konfigurasi Router OSPF Di Cisco Packet Tracer

Konfigurasi OSPF di Cisco Packet Tracer.

Contoh seperti gambar dibawah :   

Selanjutnya,
Pemberian IP Address pada setiap PC...

-  Pemberian IP  PC0 : 

IP Adress      : 172.0.10.2

subnet mask  : 255.255.255.0

gateway        : 172.0.10.1

-  Pemberian IP  PC1 : 

IP Adress      : 172.0.11.2

subnet mask  : 255.255.255.0

gateway        : 172.0.11.1

  

-  Pemberian IP  PC02 : 

IP Adress      : 172.0.12.2

subnet mask  : 255.255.255.0

gateway        : 172.0.12.1
 

Langkah Ketiga,
Selanjutnya pemberikan IP Address dan Konfigurasi OSPF pada setiap router .
Contoh sebagai berikut :

Pemberian IP Address Router0 :

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip address 172.0.10.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip address 10.10.10.1 255.255.255.252
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Router(config)#exit

Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]

Konfigurasi OSPF pada Router0 :


Router(config)#router ospf 9
Router(config-router)#net 172.0.10.0 0.0.0.255 area 0
Router(config-router)#net 10.10.10 0.0.0.4 area 0
Router(config-router)#exit

Router(config)#exit

Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]


Pemberian IP Address Router1 :

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip address 172.0.11.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip address 10.10.10.2 255.255.255.252

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Router(config-if)#exit
Router(config)#int se3/0
Router(config-if)#ip address 10.10.11.1 255.255.255.252
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]

Konfigurasi OSPF pada Router1 :


Router(config)#router ospf 9
Router(config-router)#net 10.10.10.0 0.0.0.4 area 0
Router(config-router)#net 10.10.11.0 0.0.0.4 area 0
Router(config-router)#net 172.0.11.0 0.0.0.255 area 1

Router(config)#exit

Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#


Pemberian IP Address Router2 :

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip address 172.0.12.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip address 10.10.11.2 255.255.255.252
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit



Konfigurasi OSPF pada Router2 :


Router(config)#router ospf 9
Router(config-router)#net 10.10.11.0 0.0.0.4 area 1
Router(config-router)#net 172.0.12.0 0.0.0.255 area 1
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]